News
Provide you with the latest enterprise and industry news
Provide you with the latest enterprise and industry news
Need assistance? Contact us today for expert support.
+86 18957812511 Contact UsContent
A pump station technician opens a control cabinet and sees the analog input card reading 3.6 mA instead of the expected 12 mA. The pressure transmitter is in good condition, the pump is running, but the controller has already flagged a low-current alarm and shut down the irrigation cycle. The cause is a corroded terminal. That single event shows both the strength and the vulnerability of the 4-20 mA current loop: it carries a continuous diagnostic signal that a voltage system cannot provide, yet every connection, wire, and ground point is part of the measurement.
The 4-20 mA loop remains the most widely used analog signal standard in process control, and it is especially relevant in water management, where sensors and valves are often separated by long distances. Instead of sending a voltage that can drift and drop, the transmitter controls the current in a series loop, so the value arriving at the receiver is identical to the value leaving the transmitter. The following sections explain how the standard works, how to design a loop that performs reliably, and how it fits into irrigation and industrial water systems.
A 4-20 mA current loop is a series circuit built for analog signal transmission. The transmitter, which can be a pressure sensor, temperature probe, flow meter, or any measuring device with a current output, adjusts the loop current so that 4 mA corresponds to the zero point and 20 mA corresponds to the full-scale value of the measured variable. The receiver, normally a PLC analog input or a dedicated controller, reads the current through a precision resistor and converts it into an engineering unit.
The term "live zero" is used for the 4 mA point. Keeping the transmitter at 4 mA instead of 0 mA means the loop always carries a small current, so an open circuit, a broken wire, or a disconnected connector is immediately visible as a value below 4 mA. In a 0-10 V system, 0 volts can mean either a real zero reading or a failed sensor. In a 4-20 mA loop, the two are distinguishable at a glance. Across a 250 ohm resistor, the 4-20 mA signal corresponds to 1-5 VDC, which is why analog input cards and indicator meters so often use a 250 ohm input resistor.
The main reason engineers choose current over voltage is cable resistance. Copper wire is not a perfect conductor. A 100-meter cable run with a cross-section of 0.5 mm² has a resistance of roughly 3.6 ohms. With a voltage signal and a relatively large load, that resistance creates an error that grows as the wire heats up or the distance extends. In practical terms, 0-10 V signals usually cannot be transmitted reliably over more than 50 to 100 meters without signal conditioning.
Current signals behave differently. Because the transmitter operates as a current source, the current is the same at every point in the series loop, regardless of wire length or wire resistance. As long as the power supply voltage is high enough to overcome the total voltage drops in the loop, the reading does not drift with distance. Many 24 VDC loops work comfortably over hundreds of meters, which is why analog instruments in pump stations, irrigation fields, and water treatment plants still rely on this method.
| Parameter | 0-10 VDC voltage signal | 4-20 mA current loop |
|---|---|---|
| Effect of cable resistance | Direct error proportional to cable length | No effect on the transmitted current value |
| Practical maximum distance | 50-100 m | 300 m or more with a 24 V supply |
| Fault detection capability | No live zero; 0 V can be a valid reading | 4 mA live zero; values below 4 mA indicate a fault |
| Noise susceptibility | High; voltage is affected by induced noise | Low; induced noise cannot change the series current |
Designing a reliable 4-20 mA loop does not require complex tools, but it does require respecting the voltage budget. The total resistance in the loop is the sum of the receiver resistor, the wire resistance in both directions, and any extra components, such as safety barriers or isolators. At the maximum signal of 20 mA, the loop current creates a voltage drop equal to 0.02 A multiplied by the total resistance.
Consider a typical example. The receiver resistor is 250 ohms, the sensor cable is 100 meters of 0.5 mm² twisted pair, and the transmitter needs a minimum of 10 volts to operate correctly. The receiver drop is 5 V. The wire drop for a 200-meter round trip is about 0.14 V at 20 mA. The total drop is roughly 15.2 V, so a standard 24 VDC supply leaves about 9 V of margin. That margin matters because the transmitter requires a certain minimum voltage across its terminals to regulate the current. If the total drop approaches the supply voltage, the transmitter enters saturation and the upper part of the measurement range becomes nonlinear.
For wiring, a few rules protect the loop from the most common field problems:
In an irrigation system, the 4-20 mA loop typically appears in three positions: at the sensing side, where flow, pressure, water level, or soil tension is measured; at the control side, where a PLC or irrigation controller makes decisions; and sometimes at the valve location, where an analog positioner or a proportional valve regulates flow. A pressure transmitter on the intake header sends 4-20 mA to the PLC, and the low-current alarm from that signal is often what protects the pump from running dry. A flow transmitter on the main line provides both instantaneous flow rate and totalized volume.
When the controller is a PLC, the measurement loop and the valve drive are usually separate circuits, but the design must still be coordinated. The PLC analog input determines the cable distance and the loop resistance. The valve actuator determines the power demand and the cycle speed. For battery-powered and solar-powered sites, a latching actuator is often the right choice because it draws current only during the switching pulse. The latching 2-way solenoid actuator from the IrriRich range holds the valve position without further power consumption, which is a practical advantage when the site is powered by solar rather than a utility line. The same design principle applies to larger-diameter process lines, where industrial 2-way water valves provide the full-bore flow path that keeps the pressure drop low while the analog control loop governs the actuator.
Wholesale Solenoid series LATCH 2-Way Solenoid Actuator LATCH Suppliers, FactoryNINGBO IRRIRICH WATER-SAVING TECHNOLOGY CO.,LTD is China wholesale Solenoid series LATCH 2-Way Solenoid Actuator LATCH suppliers and fact...View Product →
For flow monitoring, pulse-output water meters are a common companion to 4-20 mA transmitters. The pulse output gives a clean, isolated digital count that is easy to totalize, while the analog current loop supplies a continuous rate signal to the PLC. When a remote telemetry project requires both valve status and water volume at one connection point, the intelligent water meter valve with remote transmission can report volumetric data and be integrated into the same control scheme as the analog pressure and flow signals.
Wholesale 3WMV belt remote transmission Water Meter Valve Suppliers, Factory - NNINGBO IRRIRICH WATER-SAVING TECHNOLOGY CO.,LTD is China wholesale 3WMV belt remote transmission Water Meter Valve suppliers and factory,...View Product →
Where grid power is absent, a solar valve controller provides the switching logic and power management for latching valves, while the measurement side continues to operate from its own low-power sensor loop. This separation matters: the 4-20 mA loop has its own supply, and the actuator energy comes from the local solar source, so a failure in one circuit does not disable the other.
Solar Irrigation Solenoid Valve Controller Manufacturers, SupplierslrriRich is China Valve Controller for Irrigation Systems manufacturers and Lora control valve for farm irrigation systems suppliers, we ...View Product →Even though the 4-20 mA standard is robust, failures still occur when basic rules are ignored. The most common fault is an open loop, which is detected quickly because the current falls below 4 mA. In an irrigation schedule, a broken sensor wire can stop the pump and block an entire zone from watering. The second most common problem is excessive loop resistance, which appears as a transmitter that reads correctly at 4 mA but cannot reach 20 mA. This usually means the power supply voltage is too low for the total resistance in the loop.
Ground loops are more subtle. If the shield of the signal cable is grounded at both ends, or if the transmitter and the PLC are connected to different ground potentials, the difference causes a small current to circulate in the ground path and the measured value becomes unstable. The fix is to follow the single-point shield grounding rule and to make sure all loop-powered instruments share a common reference.
A practical commissioning sequence for a new loop is:
The 4-20 mA loop still offers an unmatched combination of simplicity, diagnostic clarity, and wide compatibility. It is not the right answer when an application needs hundreds of variables, two-way communication, or long-range wireless monitoring; in those cases, a digital protocol or a wireless gateway is more appropriate. But for a robust, low-cost, universally understood measurement signal between a sensor and a controller, the 4-20 mA loop remains the default. In irrigation and water management, where field conditions are harsh and distances are long, that reliability is worth preserving.
Understanding the Role of an Irrigation Solenoid Valve in Modern Sprinkler Systems Irrigation systems have evolved significantly over the years, moving from basic manual systems to...
READ MOREIntroduction to Solenoid Actuators What is a Solenoid Actuator? A solenoid actuator is an electromechanical device that converts electrical energy into mechanical motion through th...
READ MOREIntroduction to KGF Irrigation Solenoid Valves Brief Overview of KGF irrigation solenoid valves as a Brand and Their Presence in the Irrigation Industry KGF irrigation solenoid val...
READ MOREA plastic water meter is a device made from durable, corrosion-resistant plastic polymers that is used to measure the volume of water flowing through a pipeline. Unlike traditional...
READ MOREHehua Bridge, Yunlong town, Yinzhou district, Ningbo city
+86 18957812511
seven@irririchvalve.com
Copyright © NINGBO IRRIRICH WATER-SAVING TECHNOLOGY CO.,LTD.All Rights Reserved
